Whew. That was hard. I’m now officially “under roof”. I knew the roof would be a multi-part series, but it was more long and drawn out than I thought.
I am now far behind my goal for finishing the home in 2-3 years. In fact, I thought back in October that I might be able to finish the roof by the end of 2018. We are now halfway through 2019.
On the bright side, I’m still within budget, and now that the roof is done, I can take a breather and finish projects I left hanging like installing a motor in my pickup. Also, much of the remaining work can be done on the ground – no more dragging construction materials up to the roof. How much did I drag up there? I won’t bore you with the details, but I estimate about 35,000 lbs, not including tar paper, nails, screws and insulation. Along with the ~22,000 pounds of rafters, and the 10,000 pound ridge pole, this puts the weight of the roof around 67,000 pounds.
The shingle elevator saved my back and knees. I put 109 bundles of shingles on the roof. Each bundle weighs about 60 pounds. With the shingle elevator, I was able to load three or four bundles at a time, hook the rope to the car and back up, and then climb the ladder and off-load them onto the roof.
Also, since my roof is not exactly square, I had some issues keeping my shingle lines straight when I got to the ridge. But I noticed when watching some how-to videos that the professionals have issues with non-square roofs as well, so I feel pretty good about my not-perfect roof.
We still need to clean up the inside of the house- I’ve got scraps of foam in there, extra lumber, plywood and a lot of junk leftover from installing the roof. I noticed during a rain storm that the ground on the West side of the house is a bit higher right along the drip line than the ground is inside the house. The rain was running down to the inside of the house. I think I’ll ask the neighbor to bring his disc-harrow over and plow up that side, and then I’ll shovel the dirt to the inside of the house. That way, the inside will be just a bit higher than the outside, forcing the water to run the other direction.
I think the very next step is to trench the sewer, water, and maybe electrical. It’ll certainly be no fun to trench if I wait until after I get the subfloor in. And then I need the floor joists and the hangers, the insulation, etc., etc.
A guy I met in a sawmill group on facebook offered to make my second floor beams for really cheap. He’s in Georgia and said he’ll deliver them. I’m not ready for them, but the price is so good I can’t pass it up. I’d make them myself, but I’m currently out of trees.
Other things that need to be done in no particular order:
frame in the gables
install 1st floor
install 2nd floor
doors / windows
Sigh. The really cool part – cutting down trees, making pulleys, stacking the walls, installing the ridge pole, decking the roof- is over. From here on out, it’s almost all just normal 2×4 construction- framing, cabinets, hardwood floors, tile, plumbing, etc.
The shingle elevator was made out of wood, and it broke after the week of rain weakened it. So I welded a new one. It works better, but I’m worried about the rails it rides, which are 22 foot long 2×10’s.
I’ve made a lot of progress on the roof- the frame is complete, the insulation is completely installed on both sides. I had to stop and measure how much insulation I had left- and use the hot wire foam cutter to cut the 9″ thick pieces down to size – they were too thick to fit in the boxes. Also, I had plenty of 5″ thick pieces, but not enough 7.5″ pieces. I found that 7.5″ is the sweet spot- the foam has a stated R-value of 4.6 per inch, so a 7.5 inch thick layer gets me R34.5, where only R30 is required. This doesn’t count the value of the 2″ thick decking, or the plywood, or the underlayment, which doesn’t add much, but does add some. To make the 7.5″ thick foam, I set the wire at 7.5″ above the cutting deck, then stacked two 5.5″ pieces on top of each other and fed them through the foam cutter to make a 7.5″ stack. I have enough foam left over for a very well insulated chicken coop.
Some folks have spent thousands on their insulation- even when buying used. I was able to get away with $400 for all the foam I could stuff into a huge U-haul van and my trailer pulled behind. Extremely cheap!
2x lumber isn’t what it says it is….
I wish I had thought more about the fact that a 2×10 and 2×8 were really 1 1/2×9 1/4 and 1 1/2×7 1/4, because that threw off some of my measurements. See, the ribs are 2×10’s, spaced 48″ OC apart. But the plywood is only rated to span 24″, so I needed a support between the 2×10’s. I didn’t want to just space the 2×10 ribs at 24″ because that messes up my 48″ foam, and a 2×4 is a lot cheaper than a 2×10 no matter how you slice it. Besides, a solid piece of foam is a better insulator than a skinny 24″ strip of foam- that’s just simple physics.
Anyway, I planned to just put an 8′ long 2×4 between the 2×10 ribs, on top of the 2×8’s as a support, because the height of a 2×8 cross member + a 2×4 = height of a 2×10, right? wrong. There’s a 2″ vertical gap between the 2×8 & the 2×10, but the 8′ 2×4 laying on top of the 2×8 cross member is only 1 1/2″ thick, so there was a 1/2″ gap I had to fill between the top of the crossmember and the top of the 2×10 rib. I admit I actually couldn’t figure out at first why my plywood was sagging in the middle between the ribs. Oops.
Getting everything on the roof
Yes, this continues to be a problem. There are multiple solutions, but the main thing to remember is to keep the main thing (building the roof) the main thing. It’s easy to dream about a jib crane or some contraption with a winch motor that lifts everything up on the roof at the push of a button, but at the end of the day, the question isn’t “how did you do it?” as much as it’s “Did you do it?”. Sigh…..Up and down the ladder.
I figured out that I can lift four sheets of foam at a time with just a rope. So that helps. But the plywood is dangerously unwieldy, so I could only manage 5 sheets at a time using the elevator, or in the photo above, one at a time. In this case, it saved me carrying it from the elevator, up over the peak, and then down to be installed. You do what you have to do to get it done.
And the 2x lumber- well, I can lift about 30 of those at a time with the elevator, so that’s nice.
Nevertheless, I do have backup plans for a jib crane to lift shingles in case the shingle elevator goes kaput.
I added a 1/2″ x 1″ spacer to the 2×8 to lift the 2×4 up to the correct height. And on the boxes I hadn’t finished, I went ahead and lifted the 2×8 so that when I added the 2×4, it would be level with the 2×10. If I ever do this again…..
Using my Magnesium oil almost daily to stop the aches and pains of going up and down the ladder. It’s amazing stuff- helps the muscles heal, and protects joints.
I’ve used the car to run the elevator- just tie a rope to the front of the car, the other end goes to the pulley attached to the lift. Then back up, and everything goes up. Once it’s at the top of the lift, I climb the ladder and unload the supplies onto the roof. I carried almost every 4×8 sheet from the West side of the roof, up over the peak of the roof, and then down onto the East side of the roof. That was no fun, especially when it was a bit breezy.
I’m not sure how lifting shingles will end up- they are pretty heavy – about 60 lbs for each bundle. There are 99 of them…
I cut these in the roof to enable cool air from the ground to flow up the side of the house, into the roof, and out the peak. I made a template out of a scrap of T&G decking, then cut rectangular holes and covered them with heavy duty screen door mesh plus 1/4″ wire mesh. Here’s a video describing the theory of ventilation.
…And a change in roof design
When looking at the roof from the ground, you don’t see the built-up part of the roof, at least from the front of the home. This makes the roof look thin and wimpy.
As an aside, I’ve several folks pull up and ask about the house, and if they ask about the roof and the T&G decking, they always assume I used 1×6 planks. They are always surprised when I show them a scrap and they find it’s actually 2×6 planks. I get about one visitor a week that actually pulls up and wants to ask questions, while I get a half dozen gawkers who stop in the road to take a look or a photo. I’m always happy to answer questions- to me, the LHBA method is the best method for getting a really cheap house that has tons of value.
The last one that pulled up really made me think about this- yes it’s vain to build up the whole roof just for looks. On the other hand, the whole thing is probably vain, if you want to take a minimalist view- I mean, I could have just plopped a mobile home on the property and said, “done”, right? But let’s stay focused here- I started looking at the roof, and decided they were right. I asked my wife about it, and she immediately said, “I’ve always wanted the whole roof to be thick.” She knew the whole time, but just didn’t want to make an issue out of it. Yes, I can usually finish the maze a few seconds behind the rats….
“It’ll be a lot more work,” I said.
“And a bit more expensive – like $500 more.”
She doesn’t want to pull up and look at the wimpy roof and hate it every time she comes home. I agree.
It also simplifies the drip edge and other issues I was having with making nice clean looking roof lines.
So….I ordered more lumber, plywood, tar paper, etc. Don’t need any more shingles, luckily.
When I added the extra 2×10’s to the roof, I found that the roof decking isn’t exactly flat. Big surprise? No, not surprised. I’m actually surprised that the gap was 2″ or less. Probably due to my 5×12 rafters not being perfect or something. Anyway, to stop the critters from getting in there and make it look purdy, my wife gave me an idea – “why not put a piece of angled metal up there and screw the 2×10 to it, and then screw it to the deck?” It was a great idea, in fact:
That’s all for now…Next up: I’ll finish shingling the roof.
I searched high and low for a good price on the decking. The plans call for 2×6 Tongue & Groove, preferably in 16 foot lengths. Yes, 2 inches by 6 inches. It sounded really thick, and when I started looking on Craigslist, I could only find advertisements for 1×6. I checked the plans- nope, 2×6. I called the orange box people – they don’t sell it, and can’t even order it. I checked local mills, but you need a large volume mill – the equipment to make it is expensive. I finally found a supplier in Guntersville- just a few miles down the road. They had it for about $0.95 per foot. I ended up paying about $8,000 for a bunch of it. They delivered and unloaded it for $25.
I decided after talking to another LHBA member to polyurethane the boards before I put them up. Otherwise, you can crane your neck and do it after they are installed. That didn’t sound fun, so I laid out all the boards on the ground and bought 5 gallons of water based polyurethane. I actually bought every gallon of water based polyurethane in town. Went to 3 different orange box stores and bought them all out. The blue people didn’t have any. Then I spent 2 days painting them all. Then another day stacking them back up into piles.
First layer is the hardest
If you set the first layer incorrectly, when you reach the roof, your decking will be all cockeyed and stuff. The only way I could figure to get it correct was to measure from the exact intersection of the rafters down to the ends of the rafters. I had to “scary climb” up to the Ridgepole, set the tape, throw the tape measure off the house, go down to the ground to get it, go back up the ladder and measure to the end of the rafter. I had to do this 4 times- twice for each end of the house.
Then I ran a string between these two points, and put a nail on the string at each point it touched the rafters. Then I nailed up the first boards, using these nails as stops. After about 6 rows, I had enough to stand on, and now had to think about getting the bulk of the 500 boards up on the roof.
After all this, when I got up to the peak, it is still off by an inch or two. I figure this is due to not all the tongues and grooves fitting together perfectly. In my defense, there’s about 60 rows of boards on each side of the roof. Stuff is going to get out of wack over that distance. No matter, I’ll trim the last board a bit, maybe add some flashing just in case, and nobody will be able to tell.
Getting it up on the roof
I tried sneaking it in through the gable ends, but as the rows got higher, I ran out of space. Then I tried with a pulley to pull them up using the ladder as a rail, and the tractor on the opposite side of the house. I finally just pulled them up with a rope and pulley and nailed a pressure-treated 2×8 nailed to the rafters to prevent the boards from gouging the already-installed decking. Video here.
Installation pattern & finishing up
The manufacturer recommends one nail per rafter, 4 foot spacing between rafters, and staggering the joints. The brochure shows a couple of options. I put 2 nails per rafter, and used ring shank nails and a nail gun and air compressor. I also used a skillsaw when necessary to cut the ends off. I still need to go back and trim the decking to a one foot overhang past the ridge pole and cap logs. That will be scary- out on the edge of the roof, sawing the ends off.
Since the rafters are 48″ on center (4′ apart), and the T&G decking is 16 feet long, things tend to match up nicely. Also doesn’t hurt that I made my rafters 5 inches wide instead of 4 inches wide- provides more surface to nail the decking.
I left the rafters with overlap at the peak until now- it’s too dangerous to trim the overlaps before the decking is on. A friend recommended not trying to pin them until the decking was close enough to the top to provide a place to sit while installing them. It was good advice- even with the decking up close to where I could stand while I pinned the rafters, and even with being tied onto the roof- that 65 pound jackhammer could jump off the rebar at anytime and possibly throw me off the roof. It ended up not helping anyway- that ridge pole made out of sweet gum is very very hard- the jackhammer couldn’t pound the rebar into it. I had to resort to my sledge hammer. Even then, I bent a few pins trying to hammer them into that tough wood. Video here.
Underlayment is either tar paper or a synthetic sheet that allows the house to breathe, but keeps the moisture out. Water gets out of the house, but can’t come in. There’s a lot of debate over exactly where to place the underlayment on a built up roof. Talking with other LHBA members, I decided to place it directly on the decking. Tar paper is good stuff- it’s been in use for a hundred years and works great. But it only has a 30 day UV exposure rating. Knowing how slow I’m going, I needed something with a better rating- the synthetic I went with has a 90 day UV rating. I bought 4 rolls of it: 1,000 sq ft coverage per roll. It was about $60 a roll.
Installing the underlayment means we’ve reached an important point in the build: for the first time, my logs are out of the weather since I cut down that first tree so long ago. It is a huge, huge relief to reach this point. During the first rainstorm after installing the underlayment, I just stood inside the house, listening to the rain, but not feeling it. It is very humbling and satisfying to reach this point. We’ve got a ways to go yet to full “weather proof”, but I’ll take a little victory lap for now.
Roof insulation and finishing the roof: I have to decide between solid foam and spray foam. Solid foam might be slightly cheaper, but I have to have a thicker roof- 12″ thick compared to possibly only 6″ thick if I go with spray foam. I also have to install “sleepers”, which are like ribs- they lay on the roof and provide a space for the insulation to lay in. The sleepers can just be normal 2×6’s or 2×12’s. Or engineered wood I-beams. OSB goes on top of that (if using shingles), or furring strips (if using metal roof).
Just finishing up some minor details before I start the roof…
Since the rafters sit on top of the wall, and the roof sits on top of the rafters, there is a gap between the top of the wall and the bottom of the roof- the space between the rafters. This space in between the rafters has to be filled in with “bird blocks” to make the home weatherproof. There is some discussion on when to place the bird blocking- before adding the roof or after? I thought it would be easier to add it before, since it would be hard to fit the bird blocking in the space when the space is completely surrounded by rafters, walls and a roof, so I spent some time custom fitting some boards in between the rafters.
I used the sawmill to turn some scrap logs into 2×14’s, since the rafters are on an angle, and I wanted the bird blocking vertical. Then I toenailed each board into place. It didn’t take long- just a few days working at night.
The time changed while this was going on, so I bought some worklights and strapped them to the middle RPSL so I could keep working after dark. The cabin looks really cool all lit up at night.
Replacing a wall log
When we placed the girder log in the wall, it ended up resting on a wall log that I’ve been worried about from the time we installed it. I knew this log was “not perfect” when I installed it, but we were in a hurry, and didn’t think we had enough logs to finish the walls at the time. If you notice a log that goes “thud, thud” instead of “thunk, thunk” when hit with a hammer, this is usually an indication of rot. I’m not sure how it happened to this particular log, but since the girder log was going to rest directly on it, I thought it was prudent to replace it before I let the girder settle on it. I checked all the other logs just to be sure and they all seem to be Ok.
It turned out to be a huge pain in the rear to replace. But this is the neat thing about a Butt & Pass log home: the rebar that ties each log to the log below it also ties each log to the log above it. This means you can (if you’re nuts), cut out a log you don’t like right in the middle of the house, and it won’t fall down. Try doing that with a kit log home. Actually, no, don’t try it.
I used the “saws-all” tool with a metal cutting blade and cut the rebar out in four foot sections, then used the chainsaw to cut the log where I had cut out the rebar- I didn’t want the whole log falling out at the same time. At four feet long, the cut sections still weigh a couple hundred pounds each, so it was a little scary.
Anyway, although you can do this, it is really difficult to replace a log because you have to find one that fits exactly – same taper, same size, everything. Since that’s hard with the crooked logs we used, I had to do the best I could- I found one slightly larger- by about an inch, and dragged it over to the gap I created by removing the rotten log. I used the chain hoist and a pulley to lift it carefully into place, and then started cutting knots and bumps out of the neighboring logs as well as the new log to fit it into place.
It took me a week, working a couple hours at a time at night to get it into place. The rebar had to be installed at a slight angle since there was already logs in place around it. I think it will be fine- we’ll chink over those parts, and it will look fine. It was a sigh of relief to know that the rotten log is gone, and the new one is solid.
Next up, I get the Tongue & Groove 2″ x 6″ “car decking” installed, which is part one of getting the roof on.
I estimate the roof of my log home will weigh around 50,000 lbs. In class, they taught us that you need a girder log that is crosswise to the ridge pole to increase the strength of the structure. The girder log is also known as a collar tie. Its job is to keep the walls from spreading apart due to the weight of the roof, as well as to support the second floor.
Since we used pulleys, we knew we could install the girder log at any time after we reached second floor height. We decided to wait until now.
Height of girder log
I was stuck, though, at how high to set the girder log. Our walls are almost exactly 18 feet high. Minus one foot for the first floor and another foot for the second floor gives us eight feet for each floor. But were we supposed to put the bottom or the top of the girder log at eight feet?
I ended up calling my friend and fellow LHBA member Ivan to see what he thought. He said building code specified 6 feet 8 inches for head space: as in, don’t set the girder log any lower than 6′ 8″ from the finished floor height. That was the perfect starting point. So I added a foot to that for the finished floor height (7′ 8″), and then rounded up to 8′ and placed a mark on the wall at that height. We decided the fat end of the girder log would go over the kitchen, since on that end of the house, the girder log holds up the bedroom areas as well as the bathroom and other rooms. The other end is open to the living area, so it only needs half the joists.
Installing the girder log
Installing the girder log with pulleys is fairly straightforward: get the girder log next to the house, cut a hole in the house, attach a pulley and lift until the log is in or near the hole in the wall. Attach a second pulley through the hole and pull the log into the house. Continue to adjust pulleys and lift / pull until log reaches other side of the house. Level the log, cut another hole, and pull it through. Then pin it with rebar. Make sure it is raining – you don’t want to have too much fun. 🙂
As usual, my wife was a huge help. I pulled on one pulley with the tractor, while she let me tie the other pulley to her car. My daughter watched my hand signals from inside the car and relayed them to her mom. We are at level “pulley ninjas” at this point in the game.
Installing the Girder support log (GSL)
On smaller log homes, an angle bracket can be made to support the girder log. The bracket is bolted to the middle RPSL, and the girder log rests on the bracket. On a 40×40 log home, the span is at least 20 feet between supports, so a girder support log (GSL) is required. The GSL is not hard to find- it only has to be about eight feet long. We pulled it from a scrap log we had, and picked it so it has no knots and very little bow. I dragged it with the tractor (yes, it still weighs about 500 pounds) over to the house, then used the pulleys to drag it inside.
I knew the girder log sagged a bit in the middle by about two inches (because the string level told me so!), so I measured the space between the pier and the girder and added two inches. After doing a test fit, I cut the GSL to the right length, drilled a hole in the bottom for the rebar from the pier, and then lifted it as close as I could to the girder log, which was still sagging. I chained it in place and moved the chain hoist to the girder log and lifted the sag out of it. With the sag out of the girder, I was able to just push the GSL by hand into position. Using my favorite tool (can(t) hook), I rotated the GSL into position, then lowered the girder onto it and drove a pin through the girder to keep it from slipping. Later, I’ll install 1″ all thread and bolt the GSL to the girder. This puppy ain’t going nowhere.
We install the bird blocking, which fills in the space between the rafters and the walls. I’m calling around to get the best deal I can find on 2″ x 6″ tongue and groove car decking (which is the “hardwood floor” you see when looking up at the roof from the inside), but not having much luck finding a good deal. It looks like it will cost me about $7,000 just for this part of the roof. Still need to get the underlayment, the 2×12 sleepers for the built up roof, the insulation, plywood, and shingles or metal roof (if we can afford it). The roof really will be the single most expensive part of this build. On the other hand, I can’t wait to have the whole thing dried in.
A few weeks ago, we took a major step forward- we are done with the walls, and we got the Ridge Pole and rafters installed. I’ve spent that past 2 weeks- in between weather events and life- getting the rafters level.
Again, if we were building with 2×4’s, it’d be easy. Building with crooked logs involves a lot of finesse and finagling to get things to look right. There is nowhere to ‘zero’ my measurements, so I have to do relative measurements. For example, the cap logs are actual logs, so they vary and wave as they go along the house, which means the rafters will do the same. The rafters, as I’ve mentioned, vary as well- but they at least have one flat side.
If I don’t ‘square things up’, I’ll end up with a crooked roof. That’s what is eating up my time. And leveling and squaring the rafters is done in 3 parts: setting them at 4′ on center, then leveling at the Ridge Pole, then leveling at the cap logs.
Setting at 48″ on center
When the crane guy was on site, we were paying him a bunch of money per hour, so we decided to just get the rafters close to where we wanted. Later, I went back with a tape and measured 48 inches from front to back, and placed the rafters on this mark. Then I did the same at the cap logs. When matching up the cap log placement of the rafters with the Ridge Pole placement, I found that eyeballing it was better than trying to drop a plumb line and squaring it up that way.
leveling at Ridge Pole
This was more complicated than I thought it would be. There are quite a few variables- roof pitch, Ridge Pole taper, ridge pole bow, rafter size, bolt hole placement, and not to mention working 30’+ up in the air. Dropping tools from that height is a pain. I ended up rigging up a pulley system and buckets and strings tied to the tools and then secured to the rafters. Yes, I wore my fall harness, which was a pain, but would have been more painful to fall.
The goal here was to get them level vertically as well as horizontally. Since the RP is so wide and has a slight bow towards the East, some grooves had to be made in the RP to drop the rafter pairs down to the correct height, and at the same time move it left or right to line up with the other rafter pairs. Cutting a groove to move the rafter left or right also drops it at the same time. I measured several of them carefully, taking note of the exact placement and diameter of the RP at that point. I used graph paper to virtually drop a few of them a few inches to see what the effect would be before I cut. Once I was comfortable with my graph, I started in on the actual rafters. I used an electric chainsaw (much lighter and easier to maneuver at 30 feet up), and then smoothed the cut with an angle grinder and a rotoclip disc.
They are now all within 1/2″ of level and center.
Leveling at Cap logs
I first took a string and a string level and nailed it to the rafters on each end. Then I measured the difference between the height of the string and where it touched the rafters and recorded it in a notebook. The rafter that is furthest away from the string is the lowest, so the next step is to make all the other ones match. Unless they vary by a lot. In my case, the East side of the house varied by 8 inches across the rafters- because it kind of sags in the middle. We knew the m when we put the cap log up, but we didn’t know it was 8 freaking inches. All four corners of the house are within an inch, but it’s the ends and the middle that matters, and that’s where the difference was. There was no way I could cut 8 inches out of a 13 inch cap log- that would weaken it beyond use.
To overcome this gap, I jacked up the most offending rafters and installed two 4″x5″x14′ beams that I made on the sawmill and pinned them with rebar. This won’t be seen when the roof is on unless you know where to look because there are other boards called bird blocks that go exactly on top of the beams.
On the west side, I overcame the issue much easier with a 2×4. The rafters rest on these “jacks”, but they are still pinned with rebar through the jacks and into the cap logs.
They are now all level to within 1/2″ of each other.
Before we can install the decking on the roof, we need to install our girder log. This log acts as a ‘collar-tie’ for those in the industry. For non-industry types, the girder log keeps the walls from spreading when the 80,000 lb roof is installed. The girder also holds up the second floor. It can be installed at anytime, once the wall logs reach over the second floor. Those using telehandlers usually install it right when the wall logs reach second floor height. When using ropes and pulleys, it’s easier to wait until the wall logs are done so you have somewhere to hang the pulleys.
Click here to read Part I (where we get the Ridge Pole up)
They sent Chad out to help. He asked me about the the guy who set the Ridge Pole (RP). I told him the guy’s name, and he laughed- “Oh, yeah, good ol’ Be***! That guy’s afraid of his own shadow.” I was immediately at ease with Chad. Here’s a guy who knows that stuff like this is dangerous, and harping on it doesn’t make anyone safer. We all know it’s dangerous, and we do it anyway, but we try to work smart.
I told him the plan. “First we’re going to set that middle Ridge Pole Support Log (RPSL) right on this pier. I want you to lift it over the wall, but make sure your cable is on the far side of the RP.”
“Why is that?” he asked.
“Ok, so I figure you can lift up and down, but you probably don’t have much control on the back and forth, so I set up this pulley to do that job, but I need the cable on the backside so we don’t pull it all the way through the bottom of the RP,” I explained.
“Makes sense, let’s do it.”
I’m liking this guy. We get the RPSL hooked up, he reminds me to tie a string to the strap to release it once we’re done, and we’re off. We get it set on the pier in a few minutes. Then he comes in to fine tune it with me, with my wife supervising. With him on the pulley, and me on the cant hook, we get it placed in a few minutes. I climb up to drill and pin, and that’s it.
I took a little break, thinking I had heat exhaustion: the forecast called for 95, and with the heat index, it was closer to 100 F. I was dizzy up top, and had to stop several times while hammering the pin into the RPSL. While I took a break, Julie asked if her and my daughter could swing on the crane hook. Chad said, “sure, no problem.” Obviously, he’s a very cool crane operator.
Now onto the rafters.
I showed him my idea with the loops and the pins. Using this method, I can set the rafters from the ground, and when he releases the pressure on the strap, I can easily just pull on the string, and the pins mostly just fall out. Here’s a video of installing them. Again, he says he’s never seen it done that way, but wants to see what happens. 28 rafters later, he’s convinced to never do it any other way. But I’m getting ahead of myself….
The loop idea works like a charm- I used grade stakes and welded a washer to the end so the string wouldn’t slide off. The string was a 50′ piece of paracord that I could hold onto from the ground, along with the leader rope (which also had a quick release pin). We also ended up tying a wrench to the other quick release string as weight so it wouldn’t get caught on the wall- which happened a half dozen times- I had to climb up to get it, but at least I didn’t have to shimmy out on the rafter, 30 feet up. Releasing the rafter from the ground is much safer.
The office sent him out with a 12′ spreader bar, even though I asked for a 20′ spreader bar- this bar keeps the legs of the rafters open so they fit over the walls. But 12 feet wasn’t enough, so we ended up putting the far side on first, and then on the count of “3”, he had me pull extra hard on my leader rope, and he dropped the hook at the same time, and we were able to “launch” two sets over the near wall. But it was taking a long time- it’d been 2 hours, and we’d only set four rafters. He called the office and demanded a 20′ spreader bar. I thought the crane would make things easier. It made it faster, but it was still hard. Here’s a video of installing with the wrong spreader bar. After installing a few rafters, we stopped for lunch.
After the guy brought the 20′ spreader bar, the rafters were going up in about 15-20 minutes per rafter. We had a few that we couldn’t set just exactly right, and we realized that I could just move them with a lever later, so we changed the plan to just get them close enough.
After nine hours of work, we were on the last set. People were stopped in the road, watching. Chad’s two sons came over – he lives literally around the corner. He said sheepishly that he should have come over sooner, but he’s glad he was there that day. Nelton’s wife and daughter came over, too, taking pictures and chatting with my wife. When I pulled the last pin out of the last rafter, I couldn’t help but let out a loud, “whoop! Whoop!”, to which everyone cheered. It felt like an old fashioned barn raising.
And I got a discount- Chad agreed that we wasted 2 hours with the wrong spreader bar, and that was the crane company’s fault. Also, we got a discount for paying with cash. It was expensive, but very, very worth it.
The next step involves leveling the rafters- the rafters are flat on at least one side, but the RP is tapered and crooked and bowed- not much, but enough. It’s actually really straight- But it is off by a few inches in spots. That will involve me using string and cutting some of the RP. And then we go for the roof.